Cycliq Fly6 Rear Light & Camera Review
What can one say if your editor says to you that we have been sent some techy kit to try out, and would you like to review it? Yes please?
Cycliq Fly6 is a high powered rear LED light unit, with a difference. There is a rear facing HD cam built into the sealed all weather lamp that records what’s happening behind you as you travel along on your bike ride, daily commute or just out with friends. Got your rear covered is what it says on the box.
There’s no need to worry about anything else once you have set up the lamp on your bike and done a quick test to make sure you have a decent field of view. Just remember to switch the light-unit on EVERY time you go out!
All the factual information you need about Fly6 is on their website cycliq.com. It’s an updated design from the original, so here at Cycling Shorts, we are simply going to take it out of the box, fit it to the bike, and run it for a week or so.
Firstly, at just shy under one-hundred-pounds, it seems a lot for a rear LED. Is it worth it? Let’s see.
It comes packaged all nice and neat in a stylish black and red box, padded with shaped foam to keep all the components secure during transit to the shop, or direct to the consumer via mail order.
Once opened, there is a quick set-up guide and notes about recent improvements from your customer feedback.
The lamp feels solid, robust and of a quality build. I liked the fact there were two mounting plates and bands to accommodate a multi-bike set-up. The rubber stretch mounts are more common-place these days and means you can easily remove the lamp should you park-up and leave your bike unattended, being an expensive bit of kit.
I fitted the lamp straight onto my Trek road bike without any problem. Using the aero-seat-post adapter, I found it sat perfectly square to the ground, the body design aligned to take a standard 71.5° rake.
Not knowing what sort of view would be recorded, I positioned the lamp as high as I could without it touching my small tool pouch that was sitting tightly under the saddle.
I found the re-designed mount plate difficult to handle. I’d clipped the lamp unit into the plate slot to check the fitting prior to mounting and couldn’t remove very easily at all. It certainly wasn’t going to come loose, which isn’t a bad thing. But it made me realise that fitting the two mount plates to my two bikes, probably wasn’t going to work as well as I imagined. Maybe they would free off slightly over time if I separate them from time-to-time.
To run the test, I first had to fully charge the built-in Lithium battery. Although it comes pre-charged I wanted to see how long it would take to re-charge and how long it would last, running at full LED power. You can reduce the out-put level several times to conserve energy, or reduce the glare that the main LED emits. [Via the Courtesy Dimmer, opposite the power button].
I plugged the unit into my laptop with the provided USB lead early afternoon. I’d read that the charge LED would go off once charged. Having used re-chargeable lights this Winter gone, I knew that they took a while to fully charge up at work plugged into the USB slot on my PC, and I was right. It was late evening before the LED extinguished. Ok, I’ll test the unit tomorrow then!
Setting off on my Sunday morning bike ride, I’d set the lamp to full power and off I went. Three and a-quarter hours later, back home I switched the unit off. The unit had created a folder on the media card and sliced the ride into ten-minute videos. So they were twelve time indexed files created. I’d noticed that the first hour or so files had already been deleted, not a problem as the unit is there to safeguard any footage of an incident an hour prior to an incident and an hour after the trigger has been set through the bike laying on the ground.
Aimed as a safety back-up device designed to tell a story of what you were doing prior to any incident, then this lamp is a great way of providing additional evidence after the event. You simply must use it on every occasion that you jump on your bike, especially if commuting through town where things can sometimes get a bit more demanding.
The footage the camera produced was of a decent quality to see how the bike ride unfolded. Coming in ten-minute bite size pieces, it provides great footage that can easily be shared amongst friends and family. The file sizes produced are around four-hundred and fifty megabits each, and on the supplied card will hold around eighteen full files.
The recommend free Video Editing software worked a treat too. I found it reasonably easy to cut a couple of pieces from two files and join them to make a short demo.
On my first full power test, I achieved five-and-three-quarter hours recording before the video switched off leaving only the light working. This should last for another hour before being fully depleted.
I would imagine a normal user would need to re-charge the unit twice a week to keep the video camera working on the loop.
On the whole, having used the Cycliq Fly6 for the past four weeks, I would recommend it for my main rear light. Although a bit pricey on my initial glance, considering the beneficial footage that this device records and stores, then it’s a price worth paying.
It may not be something that you would consider buying yourself when looking for a lamp for your bike. But it would make a great gift for someone, for those who are looking for additional safety for their loved ones when out riding the bike.
RRP: £99.00
For more information on the Fly6 visit: www.Cycliq.com
Best price we can find online: www.amazon.co.uk
All Images, Video and text ©www.CyclingShorts.cc / www.chrismaher.co.uk
